Classical Redwood Bed and Dresser 4-Piece Bedroom Set

Buyer Pain Points Addressed

Buyers furnishing guest bedrooms, secondary bedrooms, or boutique hotel rooms need a smaller bedroom set that still delivers the joinery integrity and material quality of a full suite. Five-piece and six-piece suites are often too large for rooms under 15 square metres, and the wardrobe component adds both cost and shipping volume that may not be needed. This four-piece bed-and-dresser set is engineered for that compact installation, focusing on the essential bedroom pieces.

The set includes a panel bed, two nightstands, and a dresser with a matching mirror. The bed uses a low headboard profile (110 cm) rather than a full canopy or four-poster height, which suits rooms with standard 240 cm ceiling height. All frame components are cut from the same batch of Dalbergia cochinchinensis, conditioned to 8 to 12 percent moisture content.

Four-Piece Configuration

• 1 panel bed frame (king 180 cm x 200 cm or queen 150 cm x 200 cm, selectable at order)
• 2 matching nightstands (48 cm x 38 cm x 52 cm each)
• 1 dresser with attached mirror (120 cm x 45 cm x 80 cm, mirror 80 cm x 60 cm)

Buyers who need a wardrobe can add one separately from our catalogue. The four-piece set is designed as a starting configuration for guest rooms or secondary bedrooms where floor space is limited.

Dimensions at a Glance

Low Headboard Panel Bed Construction

The panel bed uses a low headboard at 110 cm height, which is designed for rooms with standard 240 cm ceiling height where a full canopy or four-poster would feel oppressive. The headboard panel is a solid Siamese rosewood board, not veneered or finger-jointed, set into a grooved frame that allows it to expand and contract with humidity changes. The bed frame uses mortise-and-tenon joints at the post-to-rail connections, secured with wooden dowels. The slat base sits recessed into the side rails and supports a standard innerspring or latex mattress without a box spring.

Hand-Cut Dovetail Dresser Drawers

The dresser features three drawers with hand-cut half-blind dovetail joints at the front corners and through-dovetails at the rear. The dovetail pins are cut at a 1:6 ratio, which is the traditional Chinese furniture standard for hardwood drawers. Drawer bottoms are set in grooved sides and slide on wooden runners, not metal slides. This construction method allows the drawer to be repaired without disassembling the dresser case.

Manufacturing Process

This set follows a four-stage production sequence optimized for compact bedroom configurations:

• Stage 1 - Board Density Sorting: Siamese rosewood boards are sorted by air-dry density using a precision balance. Boards within a density range of 0.90 to 1.00 g/cm³ are grouped for this set to ensure consistent structural response across the four pieces.
• Stage 2 - Component Cutting and Grain Matching: Headboard panels are selected for boards with the tightest interlocked grain. Bed posts are cut from the straightest timber sections. Dresser rails and nightstand stiles are cut with a tolerance of plus or minus 0.3 mm.
• Stage 3 - Joinery and Assembly: Bed frame post-to-rail connections use 18 mm tenon-depth mortise-and-tenon joints. Dresser rail-to-leg connections use 16 mm tenons. Drawer dovetails are cut by hand. Nightstands are assembled with dovetail drawer boxes and floating-panel sides.
• Stage 4 - Carving and Finishing: Headboard panel and dresser drawer fronts are sanded to 400-grit. Six coats of raw lacquer are applied by hand, each cured for 24 hours and rubbed with pumice stone. The final coat achieves a satin sheen.

Quality Inspection

• Density Verification: Each component is weighed and measured to confirm it falls within the 0.90 to 1.00 g/cm³ density range selected at Stage 1.
• Bed Frame Load Test: The assembled bed frame is loaded with 150 kg of distributed weight for 24 hours. Any joint showing separation is re-fitted.
• Dovetail Fit Check: Each drawer is cycled 50 times on its runner. Any drawer binding or loosening is re-fitted.
• Moisture Audit: Three-point readings per piece using a pin-type moisture meter. Readings outside 8 to 12 percent trigger re-conditioning.
• Finish Inspection: Surface inspected under 5000K LED lighting at 30 cm distance. Runs, sags, or uncured spots are reworked.

Enterprise Capability

云霄 has produced classical redwood furniture in Xianyou County, Fujian, since 2008. The workshop maintains FSC chain-of-custody documentation and CITES export permit registration for Dalbergia cochinchinensis shipments. Specific production capacity, employee count, and client references are available upon request. OEM custom dimensions and ODM design development are supported with a 15-day design approval cycle.

Trade Fair Experience

云霄 engages with international buyers through Canton Fair and Shanghai International Furniture Fair channels. Specific exhibition dates and booth numbers can be provided on request. Buyers visiting Fujian can arrange a workshop inspection tour covering timber storage, joinery stations, and the lacquer curing area.

Packaging and Export Documentation

The bed frame ships flat-packed (posts, rails, headboard, and slat base separated) in one crate. The dresser, mirror, and two nightstands ship fully assembled in a second crate. All packaging uses ISPM-15 heat-treated timber with EPS foam corner blocks. Total gross weight is approximately 130 kg. Every shipment includes CITES export permits, FSC certificate, commercial invoice with HS code 9403.60, and a wood drying certificate.